Disability
Related: About this forumneed advice on a lightbulb changer to change lightbulbs, flared types & twist& lock types
If I stand on even a 2 step stool, I feel very unsteady, I cannot afford to fall, I'll break something.
I need a light bulb changer, I turned on the kitchen lights this am, I have 8 can lights, 7 died today. Fair enough, all of them were installed the same day 10 yrs ago.
Got a recommendation for a good one?
Effete Snob
(8,387 posts)One would think that a multiple simultaneous light bulb failure would be a symptom of a problem other than the light bulbs simply failing.
Rorey
(8,512 posts)Maybe a surge?
Effete Snob
(8,387 posts)irisblue
(34,065 posts)When I upgraded the circuit box, there is a whole house surge protector, b/c of computers & then fancy TVs.
Polly Hennessey
(7,381 posts)I tried using one and broke the bulb off in the socket. Had to have Ryan, my handyman, fix my little problem. I now go by this simple rule: If you want to live a long time, dont fall. The light bulb changers are good for one thing, picking stuff up off the floor. 😊🍷
bullimiami
(13,972 posts)I got a changer kit that screws onto a pole from Lowes quite a while back.
I use it to change floods that are about 30' up outside the house.
Its cheap and comes with a variety of options to grab bulbs. Suction cup, a couple different spring clips.
Should do the trick.
You should find them just about anywhere.
In response to the previous post.
If the bulb is frozen in the socket it will probably break off regardless if you are using a pole or not and you would still have to dig the base out.
Ive found that the adaptors do not grip that tightly and more likely would just slip on a frozen lamp.
Well maybe not the suction cup if it got an exceptionally good grip.
Oh in addition. They also have a rubber adaptors to try and remove broken off bases.
Never had to try that though.
irisblue
(34,065 posts)bullimiami
(13,972 posts)Nothing special about that one.
Danascot
(4,875 posts)to change bulbs in very high can lights. The suction cup did the job for us.
irisblue
(34,065 posts)nor did the clock on the stove, nor did the microwave timer, nor did the ground fault circuit interrupter trip.
I had the circuit box upgraded to bring a 1950s house into the power needs of the 21st cent.
All 8 light bulbs were installed within an hour of each other, all were bought from the same hardware store, same day.
I'm comfortable with the idea that after several thousand turn on turn offs, it was death by usage.
Thanks for the idea though
ret5hd
(21,309 posts)Xoan
(25,413 posts)tyrolblue
(3 posts)As an electrician I highly doubt that all of those bulbs went bad at the same time. Most can lights are wired in a daisy chain as in they feed a hot wire to one can and then jump to the other cans. If a hot wire connection (should be black wire) becomes loose or burnt then all of the other lights will not light that are down the line. After securing a light bulb changer that works for you, install a bulb the farthest away from the working can. If it does not come on, then you need to inspect the wiring in the can that is fed from the working one. Should be the one closest to the working can. Usually in this event the black wires and wirenut are the problem, however the white wire connection (neutral wire)will do the same thing because the bad white connection will not allow a return path for the current.
irisblue
(34,065 posts)I'm too physically unstable to stand on a 6 inch from the floor step stool, I truly will fall and injure myself, age and bad joi ts SUCK. I'd need the money to get the electricians I had do the upgrade up, checking the light bulbs and maybe their connectivity to the socket first seems logical to me.
But thanks, if new bulbs do not work, electrician next it is
tyrolblue
(3 posts)Actually I have been on DU daily for the past 21 years. Just posted to give you some insight as to what may have happened. To answer your question why one in the middle stayed on. It depends on where they brought the feed. The electrician could have used any one of them for the feed and went from there. Good luck!